Masimo Radical Signal Extraction Manual del operador descargar pdf (Pagina 36)

4-30 Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual 5-15-1

alarms and messages

System Messages

The following chart alphabetically lists all system messages displayed on the LCD screen,

the cause of the message and the action(s) to be taken.

The operator should become thoroughly familiar with this information before using the

oximeter for patient monitoring.

MESSAGE POSSIBLE CAUSE(S) RECOMMENDATION

AMBIENT LIGHT

• Too much light on patient

(sensor).

• Inadequate tissue cover-

ing sensor detector.

• Remove or reduce lighting.

• Cover sensor from light.

• Reposition sensor.

DEFECTIVE CABLE

• Oximeter cannot iden-

tify the connected cable

or the cable has failed.

• Inoperative or faulty cable

• Replace cable.

• Refer to the Directions for Use of the cable

being used.

INCOMPATIBLE

SENSOR

• Not a proper Masimo

sensor.

• Replace with a proper Masimo sensor.

• Refer to Section 8.

INVALID SENSOR

• Oximeter cannot

identify the connected

sensor.

• Broken sensor cable wire or inoperative

LEDs or faulty detector.

• The sensor has failed.

• Replace sensor.

• Refer to the instructions for the sensor

being used.

LOW BATTERY

• Battery charge is low.

• Charge battery by placing the Radical-7

Handheld into the Docking Station and

powering the unit with AC line power.

• Replace battery if necessary.

LOW PERFUSION

• Signal too small.

• Move sensor to better perfused site.

• Refer to Section 4, Low Perfusion.

LOW SIGNAL IQ

• Low signal quality.

• Ensure proper sensor application.

• Move sensor to a better perfused site.

• Refer to Section 4, Signal IQ.

LOW SpCO CONF

•

SpCO measurement

reading is obscured.

• Ensure proper sensor application.

• Check sensor to see if it is working

properly.

• If not, replace the sensor.

LOW SpMet CONF

• SpMet measurement

reading is obscured.

• Ensure proper sensor application. Check

sensor to see if it is working properly.

• If not, replace the sensor

SPEAKER FAILURE

• Unit requires service

• Contact Masimo Tech Support.

• Refer to Section 9 Service and repair.

NO CABLE

• Cable not attached or

not fully inserted into

the connector.

• Disconnect and reconnect cable into

connector.

operation

To return from SatShare operation to normal standalone operation, simply disconnect

the SatShare cable from the patient monitor or disconnect the SatShare cable from the

SatShare connector on the back of the Radical-7 Pulse CO-Oximeter.

Home Mode Operation

The Radical-7 Pulse CO-Oximeter can be placed into the Home Mode to protect unquali-

fied users from changing the Radical-7 Pulse CO-Oximeter alarm settings and operation.

Entering a password does not automatically reset the Radical-7 Pulse CO-Oximeter to the

Normal operating mode. In the Home Mode, a password is required to access the menu

system and the touch key control buttons and icons.

NOTE: When the Radical-7 Pulse CO-Oximeter is set to operate in the Home mode the

default values that the Radical-7 reverts to after a power cycle are set according to

Section 3, Monitor Setup, with the exception of the Alarm Silence setting, which is

set to the pre-power down setting.

Password Operation

The Radical-7 Pulse CO-Oximeter password is 2-3-1. To enter the password use the touch-

key control buttons to the right or bottom of the LCD display and press the buttons in the

sequence shown in the following figure:

XX X

Then press 

3 3

First press 

2 2 2

1 1

Finally press 

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 55 56

Comentarios a estos manuales

Sin comentarios

Masimo Radical Signal Extraction Manual del operador Pagina 36

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Masimo Radical Signal Extraction