Masimo Radical Signal Extraction Manual del operador descargar pdf (Pagina 18)

3-2 Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual 3-3

setup

Monitor Setup

The Radical-7 Pulse CO-Oximeter maintains three types of default values which will

automatically revert to after a power cycle:

■ Factory – these options are restored to factory set values

■ Custom – these settings can be changed by the user and retained through the

power cycle.

■ Adult / Neo – these settings can be selected to revert to factory or hospital-deﬁ ned

values (for Adult or Neonatal) after a power cycle.

FACTORY SET DEFAULTS

The following outlines the Radical-7 Pulse CO-Oximeter option settings that can be

changed by the user but will revert back to after a power cycle.

OPTION DEFAULT SETTING

LCD SCREEN ILLUMINATION

AC Power

Battery Power

Set to maximum, level 4

Set to minimum, level 1

SENSITIVITY

Set to APOD mode

CUSTOM (USER) DEFINED SETTINGS

This mode is indicated by “Mode Custom” on the Alarms menu.

The following table outlines the options that may be changed by the user and the Radical-7

Pulse CO-Oximeter will remember after a power cycle. The default settings listed below

are those set at the factory and will revert back to if the user chooses to recall the factory

settings. (see Section 4, Display).

OPTION FACTORY DEFAULT SETTING CONFIGURABLE SETTING

DISPLAY VIEW

Set to Pleth + SigIQ

Pleth + SigIQ, Pleth Only,

Numbers

CONTRAST

Set to 32 0 to 63

AVERAGING TIME

Set to 8

2, 4, 8, 10, 12, 14, or 16

seconds

FASTS AT

Set to No Yes/No

HOME USE

Set to No Yes/No

INTERFACE ALARMS

Set to Yes Yes/No

SATSHARE NUMBERS

Set to Yes Yes/No

POWER SAVE

Set to No Yes/No

DATE FORMAT

Set to mm/dd/yy mm/dd/yy and dd/mm/yy

TIME FORMAT

Set to 12 hr. 12 and 24 hour

LANGUAGE

Set to English

See Section 4, Display for all

settings

ANALOG OUTPUT

Set to Analog 1: SpO

0-100%

See Section 4, Display for all

settings

Set to Analog 2: Pulse Rate

SERIAL OUTPUT PORT

MODE

Set to Binary

ASCII 1, ASCII 2, Binary,

Philips Vuelink, Spacelabs

Flexport

ALARM VOLUME

Set to Level 3 Level 1 to 4

INITIAL BATTERY CHARGING

Before use, the Radical-7 Pulse CO-Oximeter Handheld battery and the optional

Docking Station battery needs to be fully charged.

To charge the batteries:

1. Attach the Handheld unit to the Docking Station.

2. Plug in the AC power cord to power entry module. Make sure it is securely plugged

in.

3. Plug the AC power cord into an AC power source.

4. Verify that the batteries are charging.

The battery charging LED indicators on the Docking Station flash prior to charging and

remain illuminated while the batteries are charging.

Refer to Section 9, Battery Operation and Maintenance, for proper battery charging.

INITIAL INSTALLATION

Place the Docking Station on a stable hard flat surface near the patient. Always place the

Radical-7 Pulse CO-Oximeter unit on a dry surface. Maintain a minimum of 3 cm (1 inch)

free space around the Radical-7 Pulse CO-Oximeter Standalone unit. Make sure that the

Radical-7 loudspeaker is not covered to avoid a muffled alarm sound.

The Radical-7 Pulse CO-Oximeter Handheld, Docking Station or Standalone should not

be operated outside the following environmental conditions:

OPERATING ENVIRONMENTAL CONDITIONS

TEMPERATURE

+5°C to +40°C, +41°F to +104°F

HUMIDITY

5% to 95%, non-condensing

OPERATING ALTITUDE

1060 mbar to 500 mbar pressure

-1000 ft to 18,000 ft (-304 m to 5,486 m)

Configure the unit for your regional power line frequency (50 or 60 hz) if needed. Default is

60 hz (standard for the United States). See Section 4, Operation, Config.

CAUTION: THE UNIT MUST BE CONFIGURED TO MATCH YOUR LOCAL POWER

LINE FREQUENCY TO ALLOW FOR THE CANCELLATION OF NOISE

INTRODUCED BY FLUORESCENT LIGHTS AND OTHER SOURCES.

setup

3-2

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 55 56

Comentarios a estos manuales

Sin comentarios

Masimo Radical Signal Extraction Manual del operador Pagina 18

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Masimo Radical Signal Extraction