Masimo Radical Signal Extraction Manual del operador descargar pdf (Pagina 19)

3-4 Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual 3-5

Satshare Setup

The Radical-7 Pulse CO-Oximeter has been proven to be accurate during patient motion

and low perfusion conditions. Saturation and pulse rate values from the Radical-7 Pulse

CO-Oximeter may be displayed on a multiparameter monitor through the SatShare fea-

ture.

The SatShare feature provides an ideal, simulated waveform corresponding to the mea-

sured saturation and pulse rate values determined by the Masimo SET technology. This

waveform may be used to display these values on multiparameter monitors through the

multiparameter monitor’s oximetry sensor or input connector.

It is recommended that the Radical-7 Pulse CO-Oximeter is positioned close to the mul-

tiparameter monitor with the Radical-7 Pulse CO-Oximeter screen visibly displaying the

plethysmographic waveform and the saturation and pulse rate measurements.

CAUTION: SIMULTANEOUS USE OF SATHSARE AND SERIAL PORT IS NOT

SUPPORTED.

SATSHARE SETUP

1. Select the SatShare cable that is appropriate for the multiparameter monitor that is

being connected. Check the Masimo web site at www.masimo.com for the latest

list of available SatShare cables and validated instruments.

2. Connect the labeled end of the cable to the SatShare Cable Connector port on

the back of the Docking Station. Tighten the connector screws for a secure con-

nection.

3. Connect the other end of the SatShare cable either to the sensor connector of

the multiparameter monitor’s SpO

cable or directly to the SpO

connector on the

monitor.

4. Verify that the Radical-7 Pulse CO-Oximeter recognizes the correct cable. The

name of the SatShare cable will be displayed on the LCD screen when the

SatShare mode is functional.

5. Set the multiparameter monitor’s high and low saturation and pulse rate alarm

limits as appropriate.

6. Set the multiparameter monitor’s averaging time to the lowest setting (i.e. fastest

140

12:23:11pm

3.0

0.3

120

Sensor Off

setup

OPTION FACTORY DEFAULT SETTING CONFIGURABLE SETTING

PULSE BEEP VOLUME

Set to Level 4 Level 1 to 7

TREND DISPLAY

PARAMETERS

Set to %SpO

+ BPM

See Section 4, Display for

all settings.

TREND PERIOD

Set to 1 Hr.

See Section 4, Trend Setup

for all settings.

LOW SpO

ALARM LIMIT

Set to 0

(Refer Section 4, Display

for details on this user

adjustable feature)

SpMet HIGH/LOW ALARM

LIMIT

Set to High: 3.0/Low: ---

See Section 4, Alarms for

all settings.

SpCO HIGH/LOW ALARM

LIMIT

Set to High: 10/Low: ---

SMART TONE

Set to No Yes/No

ADULT/NEO (HOSPITAL DEFINED) SETTINGS

The following table outlines settings that may be defined by the hospital. If enabled (via a

password protected screen, see Section 4 Password Operation), these settings will return

to pre defined values after a power cycle. This mode is indicated by “Mode Adult” or “Mode

Neo” on the Alarms menu. See Section 4, Operation for details on enabling and setting

these parameters.

OPTION CUSTOM SETTING

ADULT / NEO SETTING

(PRE DEFINED)

SpO

HIGH/LOW ALARM

LIMIT

Set to High: ---/Low: 90

Same settings

PULSE RATE HIGH/LOW

ALARM LIMIT

Set to High: 140/Low: 50 BPM

SpMet HIGH/LOW ALARM

LIMIT

Set to High: 3.0/Low: ---

SpCO HIGH/LOW ALARM

LIMIT

Set to High: 10/Low: ---

ALARM SILENCE

Set to 120 seconds

ALARM VOLUME

Set to 3

ALARM DELAY

Set to 5

setup

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 55 56

Comentarios a estos manuales

Sin comentarios

Masimo Radical Signal Extraction Manual del operador Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Masimo Radical Signal Extraction