Masimo Radical Signal Extraction Manual del operador descargar pdf (Pagina 21)

3-8 Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual 4-14-1

operation

Introduction

To operate the Radical-7 Pulse CO-Oximeter effectively, the device must be set up prop-

erly and the operator must:

 Know how the Pulse CO-Oximeter derives its readings (see Section 1, Pulse CO-

Oximetry).

 Be familiar with its controls, components and operation.

 Understand its status and alarm messages (see Section 5, Alarm and Messages

and Section 6, Troubleshooting).

Basic operation

GENERAL SETUP AND USE

1. Inspect the Pulse CO-Oximeter case for damage.

Connect a patient cable or a direct connect sensor to the Patient Cable Connector of

the Radical-7 Pulse CO-Oximeter. Make sure it is a firm connection and the cable is

not twisted, sliced or frayed.

3. If utilizing the Standalone setup, ensure that the power cord is plugged into the Power

Cable Connector of the Docking Station and into the AC power.

If utilizing a patient cable, select a sensor that is compatible with the oximeter and the

patient before connecting it to the patient cable. See section 8, Sensors and Patient

Cables. If using a single patient adhesive or disposable sensor, check that the emitter

(red light) and the photodetector are properly aligned. Remove any substances that

may interfere with the transmission of light between the sensor’s light source and

photodetector.

Refer to the Directions for Use of the sensor before attaching the sensor to the

patient.

6. With a single patient adhesive or disposable sensor, connect the sensor to the patient

cable with the logos lining up; make sure it is a firm connection.

7. Press the Power/Standby button to turn the Pulse CO-Oximeter on.

8. Make sure the display window is free of alarm and system failure messages (see

Section 5, Alarm Identification).

9. On the display, verify:

• The high and low alarm limits for SpO

, SpMet*, SpCO* and pulse rate.

• The readings for SpO

, SpMet*, SpCO*, pulse rate, perfusion index and PVI.

NOTE: “- - - “ will remain lit on the numeric display until the SpO

, SpMet*, SpCO*, pulse

rate and PI readings have stabilized (less than 15 seconds for SpO

and up to 25 seconds

for SpMet* and SpCO*).

* If these parameters are installed in the unit.

RadNet Setup

CAUTIONS:

 AFTER CONNECTING THE SERIAL CABLE TO THE SERIAL PORT, SATSHARE

MONITORING WILL NOT BE SUPPORTED.

 SpMet AND SpCO CANNOT BE DISPLAYED ON THE MULTIPARAMETER MONI-

TOR WITH RADNET.

NOTE: Confirm that the Radical Docking Station is RadNet Ready before preceeding.

This is done by pressing the Menu button then selecting Output. Confirm that

the “D-Station” software is version R4.5.0.1 or higher.

1. Select the ASCII 2 selection from the Serial options on the Output Menu on the

Radical-7 Pulse CO-Oximeter.

2. Connect one end of the serial cable to the Serial Output connector on the back of

the Docking Station.

3. Connect the other end of the serial cable to the RadNet Interface Module connec-

tor.

4. Turn the RadNet Interface Module on.

5. With a properly configured RadNet Interface Module, the Radical-7 will automati-

cally display the pleth and SIQ waveforms as well as the SpO

and Pulse Rate

parameters on the screen at the RadNet Central Station.

6. The Radical-7 Pulse CO-Oximeter can be set up to audibly indicate all patient

alarms while communicating with the RadNet Interface module. Use the Interface

Alarms setting in the General menu to enable and disable audible alarms on the

Radical-7 Pulse CO-Oximeter.

CAUTION: ENSURE THAT THE RADICAL-7 PULSE CO-OXIMETER HANDHELD

REMAINS IN THE RADNET READY DOCKING STATION WHEN CONNECT-

ED TO THE RADNET CENTRAL MONITORING SYSTEM. REMOVING THE

RADICAL-7 PULSE CO-OXIMETER HANDHELD FROM THE RADNET

READY DOCKING STATION WILL CAUSE LOSS OF COMMUNICATION TO

THE RADNET CENTRAL MONITORING STATION.

CAUTION: WHEN THE RADICAL-7 IS PLACED IN ALL MUTE, THE PATIENT ALARMS

WILL NOT AUDIBLY SOUND ON THE RADICAL-7 OR THE RADNET

CENTRAL STATION. THE RADNET CENTRAL STATION WILL DISPLAY A

VISUAL ALARM.

setup

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 55 56

Comentarios a estos manuales

Sin comentarios

Masimo Radical Signal Extraction Manual del operador Pagina 21

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Masimo Radical Signal Extraction