Masimo Radical Signal Extraction Manual del operador descargar pdf (Pagina 30)

4-18 Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual Radical-7 Signal Extraction Pulse CO-Oximeter Operator’s Manual 4-19

operation

Clock

MENU ITEMS DESCRIPTION

TIME

Set the time - hour, minutes and seconds - in 24 hour format.

TIME FORMAT

Set the format of the time display as it will be shown on the front panel.

Available options are 12 hour (default) and 24 hour display.

DAY

Set the numerical day.

MONTH

Set the numerical month.

YEAR

Set the numerical year.

DAY FORMAT

Set the format of the date display as it will be shown on the front panel.

Available options are mm/dd/yy (default) and dd/mm/yy.

DISPLAY CLOCK

Set to display the date and time on the front panel by selecting Ye s or

No.

About

This displays the copyright and software versions of the Handheld and

Docking Station.

MENU ITEMS DESCRIPTION

Allows the user to view the current Line Frequency setting without a

password.

Config

MENU ITEMS DESCRIPTION

ENTER PASSWORD

Enter password. See Section 4, Password Operation.

Set to match regional power line frequency (50 or 60 Hz) to allow

for cancellation of noise introduced by ﬂ uorescent lights and other

sources. Default is 60 Hz (standard for the United States).

RAPID DESAT LIMIT

Enter password. See Section 4, Password Operation.

The Rapid Desat Limit will ignore the Alarm Delay setting if desaturation

falls below the Low SpO

alarm threshold per a user-deﬁ ned percent-

age. Audible tones are generated immediately, along with all visual indi-

cators. The Rapid Desat Limit can be set to the following:

OFF: The Alarm Delay setting will delay audible alarm tones regardless

of how deep the desaturation is below the alarm threshold.

-5: The Alarm Delay setting is ignored if the desaturation is 5% (mean-

ing 5 saturation units) below the Low SpO

alarm threshold.

-10: The Alarm Delay setting is ignored if the desaturation is 10% (mean-

ing 10 saturation units) below the Low SpO

alarm threshold.

3D Alarm System (optional)

Refer to Section 5, 3D Alarm System option.

operation

General

MENU ITEMS DESCRIPTION

AVERAGING TIME

The signal averaging time of this device can be set to: 2, 4, 8, 10, 12,

14 and 16 seconds*.

*With FastSat the averaging time is dependent on the input signal. For

the 2 and 4 second settings, the averaging times may range from 2 to 4

and 4 to 6 seconds, respectively.

FASTSAT

Select Yes to activate the FastSat algorithm. In the 2 and 4 seconds

averaging mode, the FastSat algorithm is automatically enabled.

HOME USE

Set the Radical-7 to the Home Mode. The Radical-7 will remain in the

Home Mode until the No setting is selected. A password is required to

activate or deactive this mode. See Section 4, Home Mode Operation,

for a detailed description.

INTERFACE

ALARMS

During SatShare, Philips Vuelink, Spacelabs Flexport and RadNet oper-

ation, the audible alarms can be enabled or disabled by selecting Yes or

No. The Interface Alarms cannot be disabled if the SpCO and/or SpMet

parameters are present in the Radical-7.

SATSHARE

NUMBERS

During SatShare operation the saturation and pulse rate measurements

can be displayed on the Radical-7 by selecting a SatShare Numbers

setting of Yes.

POWER SAVE

Select Yes to maximize battery-operating time of the Radical-7 while

Selecting Yes will disable Docking Station functions such as SatShare,

Serial and Analog output. Selecting No will activate these Docking Sta-

tion functions while operating on battery power. (While operating in the

Power Save mode, a power cycle of the Radical-7 may be required to

activate the Docking Station again after it has been disabled.)

SMART TONE

Select Yes to activate the SmartTone function. This will allow the audible

pulse to continue to beep when the pleth graph shows signs of motion.

Select No to turn off SmartTone.

PVI

Select Yes to display the PVI parameter. The PVI will display numerically

on the main screen and also will allow to the user to change the maxi-

mum and minimum PVI settings in the Trend Setup menu. Select NO to

deselect the parameter.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 55 56

Comentarios a estos manuales

Sin comentarios

Masimo Radical Signal Extraction Manual del operador Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Masimo Radical Signal Extraction